How do I know where my restaurant's ingredients go?
Give every dish in Intagya ERP a recipe with its ingredients and quantities, so the cashier takes them out of stock on every sale, and Without onion leaves the onion. After each stock count open the Ingredient use against the stock count report: for each ingredient it shows what the recipes say and what actually went, takes out voided plates and waste, and leaves the gap nothing explains, in quantity and money. And let the cashier and the storekeeper count without seeing the expected figure, so the count is honest.
A burger place in a residential street. The owner buys meat every week from the same butcher and knows the price well.
At month end he sat with the accountant. The meat bill was higher than last month, and sales were about the same. He asked the chef, who said: "We had more orders." He asked the cashier, who said: "We sold what we sold."
Nobody was lying. But nobody knew.
Why don't I know how much of each ingredient I used?
Because the cashier sells a "burger", and the store room holds "meat", "buns" and "onion". Nothing links the two names. So you know how many burgers you sold, and not how much meat should have left the fridge.
A stock count alone is not enough either. It tells you five kilos are left, not whether five is too little or too much.
How do I make every sale deduct its ingredients?
Write a recipe for every dish: one line per ingredient with its quantity for one plate. The burger, say: a bun, 150 g of meat, 30 g of onion, a slice of tomato and a little lettuce.
From here everything changes. When the cashier sells a burger, a bun and 150 g of meat leave stock, not a "burger". At the end of the day you know what should have been used, with nobody writing anything down.
And the customer who asks for no onion? The onion line in the recipe is tied to the With onion option. The cashier picks Without onion, and no onion is deducted. Small, but it adds up: a hundred onion-free burgers a month are three kilos you should not go looking for.
What gap between the recipe and the count is normal?
There is always a gap. A plate dropped, a plate sent back because the customer changed their mind, tomatoes that went bad in the fridge. That is not theft, but it costs money.
What matters is recording it. Voiding a plate after it went to the kitchen needs the approval of someone with the right, and the system asks whether the food was prepared. If it was, it goes on the void list with its reason, and its ingredients count as waste. The bad tomatoes go on a waste sheet.
My view: never hold anyone to a gap before you take the recorded waste out of it. You will wrong the chef, and he will stop recording.
How do I see the gap nothing explains?
After each count, open Ingredient use against the stock count from the Point of Sale or Inventory reports. Pick the warehouse and two counts. For each ingredient you see what the recipes say was used, what actually went by the counts, and what went in voids and waste.
Then the line you care about: the gap nothing explains, in quantity and in money. Rows are sorted by money, so the most expensive problem is on top. A row past the limit you set turns red.
At the burger place the gap was in meat only, and on certain shifts. It was not a thief. Portions were cut by eye instead of on a scale. He bought a scale for two hundred pounds, and the gap went back to something reasonable.
Why should the cashier count without seeing the expected figure?
Because whoever sees the figure before counting leans toward it. They count the drawer, find twenty pounds less, and recount until it "matches". Or they copy the figure straight from the screen.
The system has a switch per employee called Sees expected figures when counting. Without it, they close the register without seeing the expected amount or the difference, and type only what they found. The same goes for the storekeeper at the stock count: no quantity on hand and no difference. Only the manager sees the difference, after closing.
Start with the expensive items only. Write recipes for the dishes with meat, chicken or cheese first, and count those ingredients every week. Bread and sauces can wait a month.
Tomorrow morning: write the recipes of your five best-selling dishes, switch off expected figures for the cashier, and count the meat at the end of the week. After two counts you will see one number in money, and you will know where to look.
Read the restaurant ingredient control guide step by step
FAQ
Do I need a recipe for every dish from day one?
No. Start with the best sellers and the expensive ingredients, and add the rest step by step. A dish without a recipe sells as usual; it just deducts no ingredients.
Does the manager see the expected amount when the cashier counts blind?
Yes. The switch is per employee; the administrator and the inventory and POS managers see the figures, and see the difference on the session after it closes.
Can I print the day summary without a linked receipt printer?
Yes. The Print daily receipt button in Close register prints the session sales on a thin receipt through the browser printer, and Daily sale gives you a PDF.
Is this your business?
Want to see IntagyaERP on your own workflow?
Book a demo, tell us how your business runs, and watch the system handle a real scenario from your company.
Book a demo